ICEMCFD Hexa meshing Advanced Level Course

"Introduction
Introduction
Workshop 1 : Hexa meshing of NACA 0012 3D wing with different configurations
Introduction
Layout of workshop and important files
Creating NACA 0012 airfoil and domain from coordinates
Creating circular domain and square trailing edge from previous model
Creating 3D domain from 2D geometry in ICEMCFD and part names
Geometry files for all four cases
Blocking strategy for case 1 : Rectangular domain with sharp TE airfoil
Blocking splitting, block collapse and association to airfoil
Blocking adjustment in tip region
O-Grid and Y-Grid in tip region
Pre-mesh on airfoil & domain and using scan plans to inspect mesh
Blocking optimization, quality check and mesh export for Case 1
Another blocking approach for tip region for Case 1
Case 2 : Blocking approach and key features
Case 2 : Tip region - Similar approach as of case 1
Blocking approach for case 3
Blocking approach for case 4
Moving 3D Airfoil by 10 AoA in Rectangular domain
WS 2 : Hexa meshing of Square Pipe/Duct
Blocking and premesh for square duct
WS 3 : Hexa meshing of cube in external flow
Introduction
Blocking approach and creating solid block
Final Mesh
WS 4 : Hexa meshing of Quarter Pipe
Blocking method and meshing for quarter cylinder
WS5 : Hexa meshing for 3D triangular vortex generator
Blocking creation and block split
Association, merging vertices, Y-Grid and Pre-Mesh
Mesh check from Pre-mesh info and edit mesh tab
WS 6 : Hexa meshing of transition piping system
Blocking and pre-mesh of pipe assembly with various radii
WS 7 : Hexa meshing of hemisphere in two type of flow applications
Blocking and meshing for case 1 with method 1
Blocking and meshing for case 1 with method 2
Blocking and meshing for Case2 - Initial blocking
Blocking and meshing for Case2 - OGrid and Pre-Mesh
WS 8 : Hexa meshing of Venturi Scrubber
Introduction to Venturi Scrubber
Blocking approach for ventrui scrubber
Blocking splits for major regions and deleting extra blocks
Blocking splits for throat and nozzles
Association, O-Grid for three nozzles, part mesh setup and premesh for approach
Second blocking approach for venturi scrubber
WS 9 : Hexa meshing of Injections for three fluids : Air, Straw and Coal
Introduction
O-Grid for three inlets
Association and moving vertices to optimize blocking
Futher working on vertices to refine the blocking
Setting pre mesh parameters
Editing edges of blocking to increase quality of mesh
WS 10 : Hexa meshing of Gas Turbine Combustion Chamber with Periodicity
General discussion about the problem
Creating quarter O-Grid and adjusting blocking to geometry
Setting blocking with move vertices command
Deleting blocks (permanently) and merging vertices
Defining periodicity in blocking and association
Creating O-Grids for upper section and fine tuning of blocking
Final Association of edges to curves and vertices to points
Checking periodicity on vertices and faces and mesh export
WS 11: Hexa meshing of Supersonic Converging-Diverging Nozzle with extra inlet
Introduction
Creating half O-Grid and split for capturing geometry
Splitting and associating blocking at key locations
Deleting block permanently and fine tuning blocking
Further improvements in blocking
Splitting block for injection hole
Extrude block along curve for the injection hole
O-Grid for injection and final touches to mesh. Mesh check in Fluent
WS 12 : Hexa meshing of U-Bend
Introduction
Creating 3D block and adjusting to geometry for method 1 : Top down approach
Association, edge editing and premesh
O-Grid Generation
Creating same blocking and mesh using method 2 - Bottom up approach
WS 13 : Hexa meshing of Dimple
Introduction
Geometry accuracy in any CFD model
Blocking approach and premesh
WS 14 : Hexa meshing of Tripe Wedge in external flow
Introduction
Blocking strategy, association and meshing for wedge
Y block on triple wedge leading edge, Premesh, mesh export and mesh in Fluent
WS 15 : Hexa meshing of Cone
Problem description and geometry details
Creating block and splitting it at major locations
Creating O-Grid in domain and around cone
Solid block and adjusting vertices on cone
Adjusting and fine tuning block on cone
Face to surface association and premesh
Concluding remarks"