-
All
-
Online
-
Filters
-
Location
-
Type of studies
-
+ Filters (1)
NETA Training courses
- Training
- Blended in Stockton-on-tees
- 5 Days
...required angles, how to use sling charts Typing knots, bends and hitches Lifting safely both out of balance loads, balanced loads and tandem lifting...
- Training
- Blended in Stockton-on-tees
- 2 Days
...Suitable persons should, have experience and technical knowledge of cranes and lifting but may or may not have had any formal training. This course...
- Training
- Blended in Stockton-on-tees
- 1 Day
...cranes Calculating the weights and centres of gravity of loads and taking these factors into account of slinging and moving same They will also have...
- Training
- Stockton-on-tees
- 1 Day
...of movement of Pendant Cranes. Planning of method to be used in moving load. Safe loading rules (weight, height, clearance etc). Coded Workshop Practice...
- Training
- Stockton-on-tees
- 1 Day
...Rigging Regulations and Practices of the Construction Industry...
- Training
- Blended in Stockton-on-tees
- 2 Days
...of gravity of loads and taking these factors into account of slinging and moving same. They will also have a working knowledge of all relevant current...
- Training
- Blended in Stockton-on-tees
- 3 Days
...same They will also have a working knowledge of all relevant current legislation relating to lifting, slinging and rigging of general site and workshop safety standards...
- Training
- Billingham
- 3 Days
...The aim of this course is to provide a working knowledge of the 17th Edition IEE Wiring Regulations...
- Training
- Billingham
- 1 Day
...Understanding the general characteristics of an installation. Complete a 1 hour 30 Question on-line examination To provide a working knowledge of the changes...
- Training
- Billingham
- 2 Days
...electrical apprenticeship or undertaking an electrical qualification which required the AM2 Skill test Delegates must be in an electrical apprenticeship...
- Training
- Billingham
- 10 Days
...On completion of Part B the delegates should be able to. Work safely on electrical equipment within the scope of the Electricity at Work Regulations...
- Training
- Billingham
- Beginner
- 5 Days
...Make off cable terminations correctly using SWA glands. Understand the principles of a direct#19;on#19;line motor control. Identify the safely requirements...
- Training
- Billingham
- 4 Days
...Suitable for: Pre Requisite Personnel with craft, technician or engineer level experience in electrical inspection and testing. Delegates should have completed...
- Training
- Billingham
...On successful completion of the course the delegates will have an understanding of: Ex01 - Preparation and Installation of Ex'd' 'e' 'n' and 'p' systems...
- Training
- Billingham
- 2 Days
...Ex04R - Inspectional and Maintenance for Intrinsically Safe Circuits. Suitable for: CompEx is a national training and assessment scheme for electrical...
- Training
- Billingham
- 2 Days
...equipment for use in hazardous areas. the IP code for ingress protection *identification for hazardous area equip This course is intended primarily...
- Training
- Billingham
- 3 Days
...atmospheres containing combustible...
- Training
- Billingham
- 5 Days
...and knowledge of personnel with regard to process instrument control...
- Training
- Billingham
- 1 Day
...safety and welfare and environmental issues, so that after an appropriate site induction candidates will be able to work at significant less risk to themselves and others...
- Training
- Billingham
- 2 Days
...The learning outcomes of the CCNSG Nationally Accredited Safety Passport course are to increase awareness of health, safety and welfare and environmental issues... Learn about: Some knowledge of site safety is advantageous, No previous knowledge is required...