-
All
-
Online
-
Filters
-
Location
-
Type of studies
-
+ Filters (1)
NETA Training courses
- Training
- Blended in Stockton-on-tees
- 5 Days
...Course Objectives On completion of this course the learner will be capable of: Identifying basic equipment used in rigging Using safely and effectively...
- Training
- Blended in Stockton-on-tees
- 2 Days
...The aim of this course is to provide uniformity of training to a recognised standard and to provide selected personnel with the knowledge and skills needed...
- Training
- Blended in Stockton-on-tees
- 1 Day
...cranes Calculating the weights and centres of gravity of loads and taking these factors into account of slinging and moving same They will also have...
- Training
- Stockton-on-tees
- 1 Day
...of movement of Pendant Cranes. Planning of method to be used in moving load. Safe loading rules (weight, height, clearance etc). Coded Workshop Practice...
- Training
- Stockton-on-tees
- 1 Day
...Rigging Regulations and Practices of the Construction Industry...
- Training
- Blended in Stockton-on-tees
- 2 Days
...Using 'Safe Working Load' Charts. Slinging and moving loads. Assisting with cranes and the correct use of hand signals. Calculating the weights and centres...
- Training
- Blended in Stockton-on-tees
- 3 Days
...same They will also have a working knowledge of all relevant current legislation relating to lifting, slinging and rigging of general site and workshop safety standards...
- Training
- Billingham
- 3 Days
...On completion of this training course each delegate should be capable of: Understanding the requirements of the Regulations. Checking requirements for a Standard Installation...
- Training
- Billingham
- 1 Day
...Understanding the general characteristics of an installation. Complete a 1 hour 30 Question on-line examination To provide a working knowledge of the changes...
- Training
- Billingham
- 2 Days
...electrical apprenticeship or undertaking an electrical qualification which required the AM2 Skill test Delegates must be in an electrical apprenticeship...
- Training
- Billingham
- 10 Days
...and test windings and insulation of 3-phase and single-phase machines. Construct and understand control circuits including Softstart D.O.L./Star Delta...
- Training
- Billingham
- Beginner
- 5 Days
...be from a craft engineering discipline The aim of this course is to give basic Electrical Skills to Personnel of other disciplines. On completion of...
- Training
- Billingham
- 4 Days
...17th edition IEE Wiring Regs. To successfully carryout the practical assessments and written examination as required by City & Guilds, to obtain the...
- Training
- Billingham
...On successful completion of the course the delegates will have an understanding of: Ex01 - Preparation and Installation of Ex'd' 'e' 'n' and 'p' systems...
- Training
- Billingham
- 2 Days
...Ex04R - Inspectional and Maintenance for Intrinsically Safe Circuits. Suitable for: CompEx is a national training and assessment scheme for electrical...
- Training
- Billingham
- 2 Days
...working or as an introduction to the main CompEx courses...
- Training
- Billingham
- 3 Days
...atmospheres containing combustible...
- Training
- Billingham
- 5 Days
...On completion of the course delegates will be able to: Confirm understanding of the need to measure & control pressure, level flow & temperature in...
- Training
- Billingham
- 1 Day
...See Course Description. Suitable for: Card must NOT have expired beyond 3 months as prescribed by the awarding body Card must NOT have expired beyond...
- Training
- Billingham
- 2 Days
...The learning outcomes of the CCNSG Nationally Accredited Safety Passport course are to increase awareness of health, safety and welfare and environmental issues... Learn about: Some knowledge of site safety is advantageous, No previous knowledge is required...